项目编号:mcuclub-jj-053

仿真连接:点击跳转

51实物链接:点击跳转

32实物链接:点击跳转

32设计说明书上链接:点击跳转

总字数:13000+

摘要:本设计所研究的是实现一个宠物自动喂食器,即先将宠物饲料放入其中,通过设定五个喂食时间点,当到达这一时间点后,系统发出喂食信号吸引宠物,自动进行喂食。本设计主要研究如何设定五个时间点并发出喂食信号。宠物喂食器系统主要包括单片机控制、自动开关和蜂鸣器提示、倒计时间设定系统。喂食器的喂食过程,通过键盘设定五个倒计时间,当依次到达这五个时间时,发光二极管发光,蜂鸣器发出响声,吸引宠物过来进食并自动投放食物。本设计解决了工作时或节假日时由于主人不在不能对宠物进行喂食,避免了宠物由于饮食不正常所产生的问题。

在整个系统中,利用单片机对各个系统进行控制。 倒计时系统时间通过六位七段数码管显示出来。利用键盘设定五个倒计时间,单片机不停的读取时间,并判断是否到达喂食时间。开关系统电阻和发光二极管表示 ,发光二级管收到低电平时导通表示开关打开投放喂食。同时接有蜂鸣器,当到达喂食时间后蜂鸣器发出响声吸引宠物进行喂食。

关键词:智能;定时喂养;单片机;

AbstractThe study design is to achieve an automatic pet feeder, pet feed into which will set the five fed point, when you reach this point in time, automatically feeding. The main point of how to set the time within the pet food put out. Pet feeder system includes MCU control, automatic switch and music alert system, the remaining time setting system. Feeder feeding process, the five remaining time set by the keyboard, when the order reaches the five time, while the timer chip to send a signal relay and music, music playback chip, a piece of music attracted the pet, the relay switch is closed So that a red light emitting diode, said switch delivery of food. This design solves the holidays when work or not is not the owner of the pet to feed, to avoid the pet food is not normal because the problems arising.

Throughout the system, the use of single chip control system of each. Countdown to the system time by six out of seven segment digital display. Using the keyboard to set the five remaining time, microcontroller reads the stop time and to determine whether the feeding time arrives. Switching system by the relay and the light-emitting diode, said switch is closed when the relay received high light-emitting diode, said switch is running feeding. Tip has a music system, when the arrival time after feeding a piece of music tips music playback chip to feed pets.

Keywords: intelligent; automatic feeding; MCU

1 引 言

1.1 选题背景及实际意义

1.2 国内外发展历程

1.3 本论文研究目标

2系统设计方案

2.1 主要元器件选择

2.1.1 主控芯片选择

2.1.2 显示方案选择

2.1.3 按键模块方案选择

2.2 整体设计方案

3 硬件设计

3.1 主控电路模块

3.2 继电器模块

3.3AT24C02存储模块

3.4 蜂鸣器报警模块

3.5 OLED显示模块电路

3.6 独立按键电路模块

3.7蓝牙(ECB02)

4 系统程序设计

4.1 编程软件介绍

4.2 系统主流程设计

4.3 独立按键

4.4 存储模块子流程

4.5 OLED显示流程设计

4.6 蓝牙模块子流程

5 实物测试过程

5.1 整体实物调试图

5.2 上电运行实物测试

5.3 定时投喂实物测试

5.4 蓝牙实物测试

6 结论

参考文献

附录

附录一: 原理图

附录二:PCB

附录三:主程序

……………..本设计说明书是配套实物和仿真的,完整的设计参考书请购买后下载,购买过程遇到任何问题请联系客服进行咨询。本资料是一次性商品,不支持退货,感谢您对单片机俱乐部的支持……………..

发表评论

后才能评论

本站所有资源版权均属于原作者所有,这里所提供资源均只能用于参考学习用,请勿直接商用。若由于商用引起版权纠纷,一切责任均由使用者承担。更多说明请参考 VIP介绍。

最常见的情况是下载不完整: 可对比下载完压缩包的与网盘上的容量,若小于网盘提示的容量则是这个原因。这是浏览器下载的bug,建议用百度网盘软件或迅雷下载。 若排除这种情况,可在对应资源底部留言,或联络我们。

对于会员专享、整站源码、程序插件、网站模板、网页模版等类型的素材,文章内用于介绍的图片通常并不包含在对应可供下载素材包内。这些相关商业图片需另外购买,且本站不负责(也没有办法)找到出处。 同样地一些字体文件也是这种情况,但部分素材会在素材包内有一份字体下载链接清单。

如果您已经成功付款但是网站没有弹出成功提示,请联系站长提供付款信息为您处理

源码素材属于虚拟商品,具有可复制性,可传播性,一旦授予,不接受任何形式的退款、换货要求。请您在购买获取之前确认好 是您所需要的资源